CWNP Updated CWNA-109 Exam Questions and Answers by siya

OFDM is a modulation method that divides the channel bandwidth into multiple subcarriers, each carrying a single data symbol. This allows for higher data rates and more robust transmissions in multipath environments. OFDM was first introduced inthe 802.11a standard, which operates in the 5 GHz band and supports data rates up to 54 Mbps. Later, the 802.11g standard adopted OFDM for the 2.4 GHz band, and the 802.11n and 802.11ac standards enhanced OFDM with features such as MIMO (Multiple Input Multiple Output), channel bonding, and higher-order modulation schemes to achieve data rates up to 600 Mbps and 6.9 Gbps, respectively. These standards are collectively known as the ERP (Extended Rate PHY), HT (High Throughput), and VHT (Very High Throughput) PHYs . References: [CWNA-109 Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 163; [CWNA-109Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 157.

The common spectrum analyzer view that you should use for this analysis is the Waterfall/Spectrogram view. The Waterfall/Spectrogram view shows the signal from the interfering device over time on a three-dimensional graph. The x-axis represents frequency, the y-axis represents time, and the z-axis represents amplitude or power. The color of each pixel indicates the signal strength at a given frequency and time. The Waterfall/Spectrogram view can help you identify the characteristics of the interference source, such as its frequency range, duty cycle, modulation type, and pattern. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 524; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 494.

Based on the information given, what can be determined as certainly true about this AP is that it has 4 radio chains. A radio chain is a hardware component that consists of an antenna, a radio frequency (RF) amplifier, and a transceiver. The number of radio chains indicates how many spatial streams an AP can transmit or receive simultaneously using Multiple Input Multiple Output (MIMO) technology. The notation x:y:z in an AP specification denotes the number of radio chains (x), the number of spatial streams (y), and the number of spatial streams per band (z). Therefore, a tri-band, 4x4:4, Wi-Fi 6, 802.11ax AP has four radio chains in each of its three bands (2.4 GHz, low 5 GHz, and high 5 GHz). It also supports four spatial streams in total and four spatial streams per band. It cannot be determined as certainly true that it supports four channels in each band, UL-MU-MIMO, or uses a modified OpenWRT firmware based on the information given. References: [CWNP Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 223; [CWNA: Certified Wireless Network Administrator Official Study Guide: ExamCWNA-109], page 213.

 VSWR stands for Voltage Standing Wave Ratio, which is a measure of how well the impedance of the RF cable and connectors matches the impedance of the transmitter and the antenna. Impedance is the opposition to the flow of alternating current in an RF circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. A perfect impedance match would have a VSWR of 1:1, meaning that all the power is transferred from the transmitter to the antenna, and none is reflected back. However, in reality, there is always some degree of mismatch, which causes some power to be reflected back to the transmitter, creating standing waves along the cable. This reduces the efficiency and performance of the wireless system, and can also damage the transmitter. Excessive VSWR can be caused by using poor quality or damaged cables and connectors, or by using components that have different impedance ratings123. References: CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 90; CWNA-109Study Guide, Chapter 2: Radio Frequency Fundamentals, page 86; CWNP website, CWNA Certification.